Recent content by Kimb

Thanks for your dedikation in prompt answering my many mails, this is a big help for me in understanding Innuos :cool:

as I have allready restored backup to ng, i will: 1. Use a pc, to create a backup folde => ng/ unsorted/backup 2. Do the nas backup, new, from mk3, to this folder (the innuos creates an “id folder” and all folders/content based on the mk3/ music folder (this is a very time consuming backup...

So your general recommendation to use restore to build a new Innuos is for users not keeping both servers, as I do. Is there any pitfalls in using backup to nas compared to the restore way, anyting I should be aware of or miss?.

And other idea; Can I continue using usb backup on mk3, existing, doing this will only add the new rips, and then move the usb memory to ng, and import from usb on the ng, will this methode only import the new rips, add them to the existing music on ng

I have only kept the mk3 as a ripper and in the same have a backup, So, I shouldn’t use restore backup to initial build the ng in the first place, but i should had used backup to nas NEW share from the mk3, to build the ng, and then after , use the backup to nas EXSISTING share, to add new...

Its started, the credentials were the trick I have just ripped one new cd, and would like to only backup this one cd to the ng (not the total musicfrom the mk3, as this is in place at the ng, using restore from usb. Is the trick to use “existing backup, instead of new backup.

Seen from the mk3 At step 4, setup a new shared folder/setup new backup, ensure the folder is empty => how do I create a folder at the ng At step 5, my ng is found, Step 6 and 7, is jumped At step 8, i have no credentials At step 9, choose nas folder its No show “empty”

I have been advise to have the storage in the ZEN-NG treated as a 'NAS backup' destination, so after ripping some CDs on the Mk3, I need to run another backup to update the changes, and those new albums will get exported over into the ZEN NG. But how do I set this up ?… (using the import...

Thanks

I will have a new zen ng shortly and have an existing zenith mk3 (to be used as ripper and NAS going forward). Initial load of the NG, one tb music, is there any difference in using a USB backup, or use the import function via network (sq/time/other)????

as I have seen prices in dollars it was around 7300 dollars for a bare stream3 => close to 6400 euro, and then add the cost of output modules an storage (in denmark around 1450 euro for usb lite and 2tb internal ssd, based on prices for adding to a zen ng) giving a total 8750 euro) below from uk

Correct, and SQ vise, zen NG is superior to stream3, and can be upgraded to a zenith NG (hieraki as I read it SQ vise; stream1, stream1+lpt1, stream3, zenNG, zenith NG and statement NG)

As a owner of zenith mk3 and phoenix usb, a very cost effektive sq upgrade could be, to buy a “bare” zen NG or stream3, as the player via the Phoenix usb and use the mk3 as a NAS/ripper . Then later, if needed to remove the mk3, the zen NG/stream3 can be fitted by me with 4tb m.2 NVme storage...

Thanks. How about migrate mk3 into stream3 internal and play from this, and then use the mk3 as ripper/nas, by this you have mk3 as “active” backup

Can I continue using my Zenith as a ripper/NAS to the Streamer3/Zen NG cross the network/or USB attached? I’m a happy owner of a Zenith mk3/phoenix usb reclocker and would like to upgrade SQ to either the stream3 or the zen NG + the Phoenix board. Challange is; I have 3000+ ripped CD’s stored...